PLA Fusion Adhesive

Regular price $35.00
/
Shipping calculated at checkout.

Size

PLA Fusion Adhesive is specially formulated for ProMade fans for easy application and maximum retention. PLA Fusion is one of our best adhesives for medium to high humidity.

PLA Fusion is a great option for you if:

  • You’re a beginner
  • You use ProMade fans
  • You have higher humidity conditions (works in a wide range)

Fast Facts:

  • 5 Ml bottle
  • Strength: Approximately 3 to 5 weeks
  • Viscosity: Medium
  • Drying Time: 1-2 seconds
  • Humidity: 20%-75% humidity
  • Color: Black
  • Bottles are pre-punctured.
  • All PLA Adhesives are cruelty free and never tested on animals.
  • Not sure which adhesive to try? Please take the PLA Adhesive Quiz to be matched to the right adhesive for you. Our glue quiz asks you key questions about your environment to match a glue for you.

Suggested Environment

  • Temperature: 68-74 degrees Fahrenheit
  • Under 50% Humidity: 2 second cure time
  • 50%-75% Humidity: 1 second cure time
  • Over 75% Humidity: please use a dehumidifier

Note: the higher your humidity, the faster your adhesive cures.

Ingredients:

  • Ethyl-2 Cyanoacrylate, PMMA, carbon black
  • No Animal Ingredients
  • 100% Vegan
  • Cruelty-Free
  • Latex Free

Storage:

  • Please store in cool, dark container or in our adhesive container with silica gel, out of UV light.
  • Unopened adhesive is good for 6 months.
  • Once opened, adhesive is good for 4 to 6 weeks.
  • Shake for two minutes before using.

    For more information on choosing an adhesive, please watch this video.

    Warning: this product is intended for professional use only. Do not use this adhesive for self application or to apply cluster or strip lashes.

    Liquid products, including adhesive, cannot be returned. If you are unhappy with your adhesive contact our customer service via email at sales@parislashacademy.com.

     

    MSDS

     

    MSDS |MATERIAL SAFETY DATA SHEET                                  

    Section 1 – Chemical Product and Company Identification

    MSDS NAME

    FUSION

    COMPANY ADDRESS

    825 Maestro Drive

    Reno, NV 89521, USA

    Tel:775-440-1208

     

    FOR EYELASH EXTENSIONS ONLY

     

     

    Section 2 – Composition and Ingredient Information

     

    Ingredient Component Name

    Ethyl-2-Cyanoacrylate

    CAS Number 7085-0

    Concentration 91%

     

    PMMA

    CAS Number 9011-14-7

    Concentration <5%

     

    Carbon Black

    CAS Number 1333-86-4

    Concentration <4

     

     

     

     

    Section 3 – Hazards Identification   

    Hazard Risk Classification

     

    Category 1

    Potential Health Effect

    Eye: Irritating to eyes. Causes excessive tearing. Eyelids may bond.

     

    Skin: Bonds skin in seconds. May cause skin irritation. Cyanoacrylate has been reported to cause allergic reaction  but due  to  rapid  polymerization  at the skin surface, an allergic response is rare. Cyanoacrylates generate heat on solidification. In rare circumstances a large drop will burn the skin. Cured adhesive does not present a health hazard even if bonded to the skin.

    Inhalation: Exposure to vapours above the established exposure limit result in respiratory irritation which may lead to difficulty in breathing and tightness in the chest

     

    WARNING: MAY CAUSE EYE AND RESPIRATORY IRRITATION BONDS SKIN IN SECONDS.

     

    Section 4 – First Aid Measures

     

    Inhalation

    Remove to open space with fresh air. Seek medical attention to treat symptomatically if discomfort persist

     

    Eye Contact

    Flush with water for at least 15 minutes. Get medical attention. If eyelids are bonded closed, release eyelashes with warm water by covering with a wet pad. Do not force eye open. Cyanoacrylate will bond to eye p\rotein and will cause a lachrymatory effect which will help to deboned.

     

    Skin Contact

    Soak in warm soapy water. Gently peel apart using a dull instrument. If skin is burned due to the rapid generation of heat by a large drop, seek medical attention. If lips are bonded, apply warm water to the lips and encourage wetting and pressure from saliva in mouth. Peel or roll lips apart. Do not pull lips apart with direct opposing force.

     

    Ingestion

    Ingestion is not likely. See supplemental page for emergency procedures.

     

     

     

     

    Section 5 – Fire Fighting Measures

     

    Specific Hazard

    N/A

    Flash Point

    125℃ Tagliabue closed cup

     

    Auto Ignition temperature

    485℃

     

    Flammable/Explosive Limits-lower%

    Not determined

     

    Flammable/Explosive Limits-upper%

    Not determined

     

    Hazardous Decomposition Materials

    Carbon Monoxide, Carbon Dioxide

     

    Suitable Extinguishing Media

    Dry powder. Foam and Water spray. Carbon dioxides

     

    Protective Equipment

    Fire fighters should wear positive pressure self-contained breathing apparatus

     

    Hazardous combustion products

    Trace amount of toxic and or irritating fumes may be released and the use of breathing apparatus is recommended.

     

    Unusual fire or explosion hazard

    None

     

     

     

    Section 6 – Accidental Release Measures

     

    Environmental precautions

    Ventilate Area

     

    Disposal and Clean Up

    Do not use cloths for mopping up. Flood with water to complete polymerization and scrape off the floor. Cured material can be disposed of as non-hazardous waste

     

     

    Section 7 – Handling and Storage

     

    Handling Precautions

    Avoid contact with eyes, skin, and clothing. Avoid breathing of vapors

     

    Storage

    Keep in a cool, well ventilated area away from heat

    Section 8 – Exposure Controls and Personal Protection

    Engineering Controls

    Use positive down-draft exhaust ventilation if general ventilation is insufficient to maintain vapor concentration below established exposure limits.

     

    Respiratory Protection

    Use NIOSH approved respirator if there is potential to exceed exposure limits. Observe OSHA regulations for respiratory use (29 CFR 1910.134)

     

    Skin Protection

    Use gloves and aprons as necessary to prevent contact. Do not use PVC, nylon or cotton.

     

    Eye/Face protection

    Chemical splash goggles or safety glasses with side shields.

     

     

     

    Section 9 – Physical and Chemical Properties

     

    Physical State

    Black Liquid

    Odour

    Sharp ,irritation

    pH

    N/A

    Specific Gravity

    1.04 @ 75oF

    Boiling Point

    More than 300OF

    Flash Point

    125℃ Tagliabue closed cup

    Flammability

    1

    Evaporation Rate(Ether=1)

    N/A

    Ignition Temperature

    485℃

    Melting/Freezing Point

    N/A

    Solubility

    Polymerized by water

    Vapour Density

    Approximately 3

    Vapour Pressure

    Less than 0.2mm

    Volatile Organic Compound(EPA Method24)

    87.9%

     

    Section 10 – Stability and Reactivity

     

    Stability

    Stable under recommended storage conditions

     

    Conditions to Avoid

    Spontaneous polymerization

     

    Incompatible Materials

    Water, amines, alkalis and alchols

     

    Hazardous Polymerization

    Rapid exothermic polymerization will occur in the presence of water, amines and alcohol

     

    Hazardous decomposition

    None

     


     

     

    Section 11– Toxicological Information

     

    Product toxicity data : Acute oral LD50〉5000mg/kg(rat) Acute dermal LD50〉2000mg/kg(rabbit)

     

    Carcinogen status

     

    Hazardous component

    NTP Carcinogen

    IARC Carcinogen

    OSHA

    Ethyl Cyanoacrylate

    7058-85-0

    NO

    NO

    NO

    Carbon Black

    1333-86-4

    NO

    Group 2B

    Yes

     

     

     

    Literature Referenced Target Organ & Other Health Effects

     

    Health Effects Hazardous

    Health Effects/Target Organs

    Ethyl Cyanoacrylate

    Allergen, Irritant, Respiratory

    Carbon Black

    Respiratory, Some evidence of carcinogenicity

     

     

    Section 12– Ecological Information

     

    Ecotoxicity

    No data available

    Persistence/Degradability

    No data available

    Bioaccumulative Potential

    No data available

    Mobility in Soil

    No data available

     

     

    Section 13– Disposal Consideration

     

    Information provided is for unused product only.

    Recommended method of disposal in accordance with Federal, State and local regulation

    Not a RCRA hazardous waste

    Section 14– Transport

    INTERNATIONAL AIR RANSPORT ASSOCIATION (IATA) :

    This product is not classified as dangerous goods , by rules of IATA.

     

    .S Department of transportation (DOT) Shipping regulations:

    This product is not classified as dangerous goods, per U.S. DOT regulation under 49CFR 172.101.

    Proper shipping name : MEGA X( glue for false eyelashes) Hazard Class number and description : Not applicable.

    UN identification number : Not applicable. Packing group : Not applicable.

    Section 15– Regulatory Information

    Cyanoacrylate Korean regulation

    Industrial  Safety  and  Health:  Hazardous  Chemical  management  .Dangerous  Material  Safety

    management.

    United State Regulatory Information

    TSCA 8 (b) Inventory Status : All components are listed or are exempt from listing on the Toxic

    Substances Control Act Inventory TSCA 12(b) Export Notification : None

    CERCLA/SARA Section 302 EHS : None

    CERCLA/SARA  Section  311/312  :  Immediate  Health  Hazard,  Delayed  Health  Hazard,  Fire.

    Reactive

    CERCLA/SARA 313 : None

    California Proposition 65 : No California Proposition 65 listed chemical are known to be present Canada Regulatory Information

    All components are listed on or are exempt from listing on the Domestic Substances List WHMIS Hazard class : B.3, D.2.B

     

    Section 16– Other Information

     

    DISCLAIMER:

    All the information of Material Safety Data Sheet is provided on the basis in good faith, and is believed to be trustworthy but is for reference only. Adhesive is very complicated and the result

    of it is much dependent on the surface material, additive, releasing agents of the substrates and user's methods. BTC and its agents, dealers, distributors, directors and employees do not accept any liability for the results whatsoever arising from the use of BTC products due that the utilization of these products is simply out of BTC control. The users are responsible for selecting the suitability of the products and methods of use.